Purification of arsenic-contaminated water using iron molybdate filters and monitoring of their genotoxic, mutagenic, and cytotoxic effects through bioassays.

Environmental contamination has been a cause of concern worldwide, being aggravated by anthropogenic activities carried out without the correct disposal of toxic products in the various habitats on our planet. In Brazil, mining companies are responsible for the contamination of large river basins with toxic elements from mining activities. Among these elements, arsenic draws attention because it is highly carcinogenic and found in waters in concentrations above those recommended by regulatory agencies. Here, Fe2(MoO4)3 nanoparticles are synthesized and used as a filter medium in water purification systems contaminated with arsenic. The adsorption kinetics of arsenic by Fe2(MoO4)3 nanoparticles is fast, showing pseudo-second-order rate constants of 0.0044, 0.0080, and 0.0106 g mg-1 min-1 for As3+, As5+, and MMA, respectively. The adsorption isotherms are better adjusted with the Langmuir and Redlich-Peterson models, indicating that the arsenic adsorption occurs in monolayers on the Fe2(MoO4)3 surface. The Fe2(MoO4)3 adsorption capacities determined for the As3+, As5+, and MMA species are 16.1, 23.1, and 23.5 mg g-1, respectively. The Fe2(MoO4)3 filter is efficient in purifying arsenic-contaminated water, reducing its initial concentration from 1000 µg L-1 to levels close to zero. Biological tests indicate that Fe2(MoO4)3 nanoparticles and filtered water have no cytotoxic, genotoxic, and mutagenic risks to human life. Those results suggest that the Fe2(MoO4)3 filter can be used as an efficient and safe technology for the purification of water contaminated by arsenic.

Isolation and characterization of bacteria from a brazilian gold mining area with a capacity of arsenic bioaccumulation.

In Paracatu, a city in Minas Gerais State (Brazil), the gold mineral extraction produces wastes that contribute to environmental contamination by arsenic. This work describes the evaluation of arsenic concentration from soil of a gold mining area in Paracatu and the selection of arsenic resistant bacteria. In the process of culturing enrichment, 38 bacterial strains were isolated and the minimum inhibitory concentration (MIC) was determined in solid medium for each strain. Three bacterial strains named P1C1Ib, P2Ic and P2IIB were resistant to 3000 mg L-1 of arsenite. Analysis of 16S rDNA gene sequences revealed that these bacteria belong to Bacillus cereus and Lysinibacillus boronitolerans species. After cultivation of the strains P1C1Ib, P2Ic and P2IIIb, 69.38%-71.88% of arsenite and 82.39%-85.72% of arsenate concentrations were reduced from the culture medium, suggesting the potential application of theses strains in bioremediation processes.

Gold-Coated Superparamagnetic Iron Oxide Nanoparticles Attenuate Collagen-Induced Arthritis after Magnetic Targeting.

The aim of the study was to evaluate if gold-coated superparamagnetic iron oxide nanoparticles (AuSPION) magnetic-targeted to the arthritic articulation of collagen induced arthritis (CIA) rats are able to ameliorate rheumatoid arthritis without producing significant biological adverse effects in comparison to colloidal Au nanoparticles (AuC) and metotrexate (MTX). Male Wistar rats were divided into control; arthritic; AuSPION (150 µg kg-1); AuC (150 µg kg-1) and MTX (2.5 µg kg-1). Treatments were administered thrice every other day by the intraperitoneal route 15 min after all groups had a neodymium magnet coupled to the right ankle joint (kept for 1 h). Paw edema and body weight were measured weekly. Joint sections were evaluated by Haematoxylin & Eosin and immunohistochemistry (TNF-α, IL-1ß). Biomarkers of oxidative stress were used to evaluate toxicity. Among the evaluated treatments, AuSPION led to significant clinical improvements (decreased edema and infiltration by leukocytes as well as less positively immunostained cells for both TNF-α and IL-1ß in synovium) accompanied by a lack of toxicity as indicated by redox state and genotoxicity assays. Our results clearly indicate that the magnetic targeting of AuSPION suppresses joint edema and inflammation, cytokine expression as well as the redox imbalance, thereby contributing to an amelioration of arthritis severity in CIA rats. The results demonstrate for the first time the potentiality of AuSPION administration under a magnetic field as an attractive alternative for future treatments of rheumatic diseases.

Seasonal variations, metal distribution and water quality in the Todos os Santos River, Southeastern Brazil: a multivariate analysis.

In aquatic habitats, metal contamination from natural and anthropogenic sources continues to pose a concern for human and environmental health. Thus, it is important to complete monitoring studies to assess patterns and the extent of metal contamination in these ecosystems. The purpose of this work was to determine the concentrations of 31 chemical elements and water quality parameters of the Todos os Santos River located in the Mucuri Valley, Minas Gerais, Brazil. A multivariate statistical analysis was used to determine any seasonal and spatial patterns from the data. Results demonstrated that metals including Al, Fe, and Ni exceeded Brazilian and international guidelines nutrients as P also exceed water quality standards. Principal components analysis indicated distinct geographical and seasonal patterns for multiple elements with hierarchical cluster analysis confirming the observed spatial patterns of contamination in the Todos os Santos River.

Validation of a robust LLE-GC-MS method for determination of trihalomethanes in environmental samples.

An analytical liquid-liquid extraction-gas chromatography-mass spectrometry (LLE-GC-MS) method was developed and validated for the determination of trihalomethanes (THMs) in environmental samples. The compounds studied were trichloromethane (TCM), bromodichloromethane (BDCM), dibromochloromethane (DBCM), and tribromomethane (TBM). The calibration curves for the THMs showed high linearity in the range of 1-1000 µg L-1. Studies of intra-day and inter-day precision, limit of detection (LOD), limit of quantification (LOQ), accuracy, and recovery were performed with low (10 µg L-1), medium (40 µg L-1), and high (200 µg L-1) concentrations of THMs. The intra-day and inter-day precision RSD varied in the ranges of 0.17-6.95% and 0.26-15.70%, respectively. No statistical differences were observed between the analysis of the concentration of certified reference materials (CRM 4M8140-U) and the values reported by CRM, indicating the good accuracy of the proposed method. The recovery was 88.75-119.21%. The LOD and LOQ were smaller than 0.13 and 0.40 µg L-1. Compared with reported LLE-GC-MS methods, the validated method had similar LOD and enhanced LOQ, precision, accuracy, and recovery. Also, the method is robust, selective to THMs, and the total time for the extraction and GC separation of THMs is about 18 min. The method was useful for detecting and quantifying low concentrations of TCM (40-80 µg L-1) formed by water chlorination in the presence of Microcystis aeruginosa cyanobacteria, thus demonstrating its applicability for monitoring THMs in real samples.

Purification of arsenic-contaminated water with K-jarosite filters.

The high toxicity and potential arsenic accumulation in several environments have encouraged the development of technologies for its removal from contaminated waters. However, the arsenic released into aquatic environment comes mainly from extremely acidic mining effluents, making harder to find stable adsorbents to be used in these conditions. In this work, K-jarosite particles were synthesized as a stable adsorbent in acidic medium for eliminating arsenic from contaminated water. The adsorption capacities of K-jarosite for As3+, As5+, and monomethylarsonic acid were 9.45, 12.36, and 8.21 mg g-1, respectively. Most arsenic in water was adsorbed within the first 10 min, suggesting the fast arsenic adsorption kinetics of K-jarosite particles. Because of that, a K-jarosite filter was constructed for purifying water at a constant flow. The K-jarosite filter was highly efficient to treat arsenic-contaminated water from a Brazilian river, reducing the concentration of arsenic in water to near zero. These data suggest the K-jarosite filter can be used as a low-cost technology for purifying arsenic-contaminated water in acidic medium.

Adsorption of arsenic from water and its recovery as a highly active photocatalyst.

The contamination of water with arsenic has aroused concern around the world due to its toxic effects. Thus, the development of low-cost technologies for treating water contaminated with toxic metals is highly advisable. Adsorption is an attractive technology for purification of contaminated water, but it only transfers the contaminant from water to the solid adsorbent, which provokes another problem related to solid residue disposal. In this work, we developed a sustainable method for purifying water contaminated with arsenic by using δ-FeOOH nanoparticles. The adsorption capacities of nanomaterial for As3+ and As5+ species were 40 and 41 mg g-1, respectively, and were highly efficient to purify arsenic-contaminated water from a Brazilian river. The concentration of arsenic in water was close to zero after the water treatment by δ-FeOOH. Once the arsenic is adsorbed, it can be recovered by treatment with NaOH solutions. Approximately 85 % of the total adsorbed arsenic could be recovered and used as a precursor to produce useful material (Ag3AsO4) with excellent photocatalytic activity. It was active under visible light and had a high recyclability for oxidation of rhodamine B. Finally, the simple method described is promising to design sustainable process of environmental remediation with minimum residue generation.

A fast and environment-friendly method for determination of chemical oxygen demand by using the heterogeneous Fenton-like process (H2O2/Fe(3-x)Co(x)O4 nanoparticles) as an oxidant.

An easy, fast and environment-friendly method for COD determination in water is proposed. The procedure is based on the oxidation of organic matter by the H2O2/Fe(3-x)Co(x)O4 system. The Fe(3-x)Co(x)O4 nanoparticles activate the H2O2 molecule to produce hydroxyl radicals, which are highly reactive for oxidizing organic matter in an aqueous medium. After the oxidation step, the organic matter amounts can be quantified by comparing the quantity of H2O2 consumed. Moreover, the proposed COD method has several distinct advantages, since it does not use toxic reagents and the oxidation reaction of organic matter is conducted at room temperature and atmospheric pressure. Method detection limit is 2.0 mg L(-1) with intra- and inter-day precision lower than 1% (n=5). The calibration graph is linear in the range of 2.0-50 mg L(-1) with a sample throughput of 25 samples h(-1). Data are validated based on the analysis of six contaminated river water samples by the proposed method and by using a comparative method validated and marketed by Merck, with good agreement between the results (t test, 95%).

Mercury speciation in seafood samples by LC-ICP-MS with a rapid ultrasound-assisted extraction procedure: Application to the determination of mercury in Brazilian seafood samples.

This paper describes a simple method for mercury speciation in seafood samples by LC-ICP-MS with a fast sample preparation procedure. Prior to analysis, mercury species were extracted from food samples with a solution containing mercaptoethanol, l-cysteine and HCl and sonication for 15min. Separation of mercury species was accomplished in less than 5min on a C8 reverse phase column with a mobile phase containing 0.05%-v/v mercaptoethanol, 0.4%m/v l-cysteine and 0.06molL(-1) ammonium acetate. The method detection limits were found to be 0.25, 0.20 and 0.1ngg(-1) for inorganic mercury, ethylmercury and methylmercury, respectively. Method accuracy is traceable to Certified Reference Materials (DOLT-3 and DORM-3) from the National Research Council Canada (NRCC). With the proposed method there is a considerable reduction of the time of sample preparation. Finally, the method was applied for the speciation of mercury in seafood samples purchased from the Brazilian market.

A simple method based on ICP-MS for estimation of background levels of arsenic, cadmium, copper, manganese, nickel, lead, and selenium in blood of the Brazilian population.

Throughout the world, biomonitoring has become the standard for assessing exposure of individuals to toxic elements as well as for responding to serious environmental public health problems. However, extensive biomonitoring surveys require rapid and simple analytical methods. Thus, a simple and high-throughput method is proposed for the determination of arsenic (As), cadmium (Cd), copper (Cu), manganese (Mn), nickel (Ni), lead (Pb), and selenium (Se) in blood samples by using inductively coupled plasma-mass spectrometry (ICP-MS). Prior to analysis, 200 microl of blood samples was mixed with 500 microl of 10% v/v tetramethylammonium hydroxide (TMAH) solution, incubated for 10 min, and subsequently diluted to 10 ml with a solution containing 0.05% w/v ethylenediamine tetraacetic acid (EDTA) + 0.005% v/v Triton X-100. After that, samples were directly analyzed by ICP-MS (ELAN DRC II). Rhodium was selected as an internal standard with matrix-matching calibration. Method detection limits were 0.08, 0.04, 0.5, 0.09, 0.12, 0.04, and 0.1 microg//L for As, Cd, Cu, Mn, Ni, Pb, and Se, respectively. Validation data are provided based on the analysis of blood samples from the trace elements inter-\comparison program operated by the Institut National de Sante Publique du Quebec, Canada. Additional validation was provided by the analysis of human blood samples by the proposed method and by using electrothermal atomic absorption spectrometry (ETAAS). The method was subsequently applied for the estimation of background metal blood values in the Brazilian population. In general, the mean concentrations of As, Cd, Cu, Mn, Ni, Pb, and Se in blood were 1.1, 0.4, 890, 9.6, 2.1, 65.4, and 89.3 microg/L, respectively, and are in agreement with other global populations. Influences of age, gender, smoking habits, alcohol consumption, and geographical variation on the values were also considered. Smoking habits influenced the levels of Cd in blood. The levels of Cu, Mn, and Pb were significantly correlated with gender, whereas Cu and Pb were significantly correlated with age. There were also interesting differences in Mn and Se levels in the population living in the north of Brazil compared to the south.

Identification and distribution of mercury species in rat tissues following administration of thimerosal or methylmercury.

Methylmercury (Met-Hg) is one the most toxic forms of Hg, with a considerable range of harmful effects on humans. Sodium ethyl mercury thiosalicylate, thimerosal (TM) is an ethylmercury (Et-Hg)-containing preservative that has been used in manufacturing vaccines in many countries. Whereas the behavior of Met-Hg in humans is relatively well known, that of ethylmercury (Et-Hg) is poorly understood. The present study describes the distribution of mercury as (-methyl, -ethyl and inorganic mercury) in rat tissues (brain, heart, kidney and liver) and blood following administration of TM or Met-Hg. Animals received one dose/day of Met-Hg or TM by gavage (0.5 mg Hg/kg). Blood samples were collected after 6, 12, 24, 48, 96 and 120 h of exposure. After 5 days, the animals were killed, and their tissues were collected. Total blood mercury (THg) levels were determined by ICP-MS, and methylmercury (Met-Hg), ethylmercury (Et-Hg) and inorganic mercury (Ino-Hg) levels were determined by speciation analysis with LC-ICP-MS. Mercury remains longer in the blood of rats treated with Met-Hg compared to that of TM-exposed rats. Moreover, after 48 h of the TM treatment, most of the Hg found in blood was inorganic. Of the total mercury found in the brain after TM exposure, 63% was in the form of Ino-Hg, with 13.5% as Et-Hg and 23.7% as Met-Hg. In general, mercury in tissues and blood following TM treatment was predominantly found as Ino-Hg, but a considerable amount of Et-Hg was also found in the liver and brain. Taken together, our data demonstrated that the toxicokinetics of TM is completely different from that of Met-Hg. Thus, Met-Hg is not an appropriate reference for assessing the risk from exposure to TM-derived Hg. It also adds new data for further studies in the evaluation of TM toxicity.

Methylmercury and inorganic mercury determination in blood by using liquid chromatography with inductively coupled plasma mass spectrometry and a fast sample preparation procedure.

Despite the necessity to differentiate chemical species of mercury in clinical specimens, there are a limited number of methods for this purpose. Then, this paper describes a simple method for the determination of methylmercury and inorganic mercury in blood by using liquid chromatography with inductively coupled mass spectrometry (LC-ICP-MS) and a fast sample preparation procedure. Prior to analysis, blood (250microL) is accurately weighed into 15-mL conical tubes. Then, an extractant solution containing mercaptoethanol, l-cysteine and HCl was added to the samples following sonication for 15min. Quantitative mercury extraction was achieved with the proposed procedure. Separation of mercury species was accomplished in less than 5min on a C18 reverse-phase column with a mobile phase containing 0.05% (v/v) mercaptoethanol, 0.4% (m/v) l-cysteine, 0.06molL(-1) ammonium acetate and 5% (v/v) methanol. The method detection limits were found to be 0.25microgL(-1) and 0.1microgL(-1) for inorganic mercury and methylmercury, respectively. Method accuracy is traceable to Standard Reference Material (SRM) 966 Toxic Metals in Bovine Blood from the National Institute of Standards and Technology (NIST). The proposed method was also applied to the speciation of mercury in blood samples collected from fish-eating communities and from rats exposed to thimerosal. With the proposed method there is a considerable reduction of the time of sample preparation prior to speciation of Hg by LC-ICP-MS. Finally, after the application of the proposed method, we demonstrated an interesting in vivo ethylmercury conversion to inorganic mercury.

Evaluation of the use of human hair for biomonitoring the deficiency of essential and exposure to toxic elements.

Monitoring the nutritional status of essential elements and assessing exposure of individuals to toxic elements is of great importance for human health. Thus, the appropriate selection and measurement of biomarkers of internal dose is of critical importance. Due to their many advantages, hair samples have been widely used to assess human exposure to different contaminants. However, the validity of this biomarker in evaluating the level of trace elements in the human body is debatable. In the present study, we evaluated the relationship between levels of trace elements in hair and whole blood or plasma in a Brazilian population. Hair, blood and plasma were collected from 280 adult volunteers for metal determination. An ICP-MS was used for sample analysis. Manganese, copper, lead and strontium levels in blood varied from 5.1 to 14.7, from 494.8 to 2383.8, from 5.9 to 330.1 and from 11.6 to 87.3 microg/L, respectively. Corresponding levels in hair varied from 0.05 to 6.71, from 0.02 to 37.59, from 0.02 to 30.63 and from 0.9 to 12.6 microg/g. Trace element levels in plasma varied from 0.07 to 8.62, from 118.2 to 1577.7 and from 2.31 to 34.2 microg/L for Mn, Cu and Sr, respectively. There was a weak correlation (r=0.22, p<0.001) between lead levels in hair and blood. Moreover, copper and strontium levels in blood correlate with those levels in plasma (r=0.64 , p<0.001 for Cu) and (r=0.22, p<0.05 for Sr). However, for Cu, Mn and Sr there was no correlation between levels in hair and blood. Our findings suggest that while the idea of measuring trace elements in hair is attractive, hair is not an appropriate biomarker for evaluating Cu, Mn and Sr deficiency or Pb exposure.

Simultaneous determination of Cd, Cu, Mn, Ni, Pb and Zn in nail samples by inductively coupled plasma mass spectrometry (ICP-MS) after tetramethylammonium hydroxide solubilization at room temperature: comparison with ETAAS.

A simple method is described for the determination of Cd, Cu, Mn, Ni, Pb and Zn in nails by using inductively coupled plasma mass spectrometry (ICP-MS) or electrothermal atomic absorption spectrometry (ETAAS). Prior to analysis, 10-20 mg of nail samples were accurately weighed into (15 mL) conical tubes. Then, 1 mL of 25% (w/v) tetramethylammonium hydroxide (TMAH) solution was added to the samples, incubated at room temperature overnight and then further diluted to 10 mL with 1% (v/v) HNO(3). After that, samples were directly analyzed. Rhodium was used as internal standard for ICP-MS analysis. Method detection limits (3 s, n=20) were 0.1, 3.0, 1.0, 4.5, 1.5, 5.0 ng g(-1) for Cd, Cu, Mn, Ni, Pb and Zn, respectively for ICP-MS, and 24, 26, 30, 143, 130 and 1000 ng g(-1), respectively for ETAAS. The key issue addressed here is the elimination of the acid digestion prior to analysis. Moreover, with the use of the proposed method there is a considerable improvement in the sample throughput comparing to the traditional methods using microwave-assisted acid sample digestion prior to analysis. For validation purposes, six ordinary nail samples were solubilized and then directly analyzed by ICP-MS and ETAAS, with no statistical difference between the two techniques at 95% level on applying the t-test.